ass_messages/messages.asm

org 0x7C00      ; The boot code on a drive always gets loaded at address 0x7C00
bits 16         ; .bin defaults to 16 bits

WIDTH equ 0x4F			; 79
HEIGHT equ 0x18			; 24
VIDEO_MODE equ 0x3		; 80x25 screen, text mode

PIT_MODECOMMAND_PORT equ 0x43	; programmable interval timer mode/command port (used for speaker)
PIT_CH2_DATA_PORT equ 0x42	; PIT channel 2 data port

;; see http://www.ctyme.com/intr/int-10.htm for interrupts

start:

mov sp, 0x2000	; initialise stack pointer

;; Interrupt 0x14, ah=0
;; bit 7 - 5	baud rate
;;	0 0 0	110
;;	0 0 1	150
;;	0 1 0	300
;;	0 1 1	600
;;	1 0 0	1200
;;	1 0 1	2400
;;	1 1 0	4800
;;	1 1 1	9600	(used)
;; bit 4 - 3	parity
;;	0 0	none	(used)
;;	0 1	odd
;;	1 1	even
;; bit 2	stop bits
;;	0	1
;;	1	2
;; bit 1 - 0	data bits
;;	1 0	7
;;	1 1	8

;; initialise serial port
mov ah, 0x0		; initialise UART
mov al, 0b111_00_0_11	; baud 9600, no parity, 1 stop bit, 8 data bits
mov dx, 0x0		; COM1
int 0x14

;; Use color mode
mov	ax, VIDEO_MODE
int	0x10

;; Clear screen
mov ah, 0x06	; scroll screen up
mov al, 0x00	; lines to scroll (0 = clear)
mov bh, 0x0F	; bg/fg colour
mov cx, 0x0000	; upper row number, left col number (both 0)
mov dh, HEIGHT	; lower row number (24)
mov dl, WIDTH	; right col number (80)
int 0x10

;; Set cursor to bottom of screen
;; dh already contains HEIGHT
mov ah, 0x02	; set cursor position
mov bh, 0x00	; page number
mov dl, 0x00	; col (leftmost col)
int 0x10

.loop:
	;; read a character, ASCII in al
	mov ah, 0x00	; Read character
	int 0x16

	;; a null character will be sent before every command from the virtual keyboard
	;; so if a null is detected go to the virtual_kbd_loop instead
	cmp al, 0x00	; null
	je .virtual_kbd_loop_init

	;; print character to serial port
	mov ah, 0x01	; transmit char
	mov dx, 0x00	; COM1
	int 0x14

	cmp al, 0x08 	; backspace
	je change_color_mode

	cmp al, 0x1B 	; esc
	je beep

	cmp al, 0x0D 	; enter
	je .nl

	jmp nonewline	; all other characters

.nl_reset_state:
	mov byte[is_from_virtual_kbd], 0x0	; reset state variable
.nl:
	call newline
	jmp .loop

.virtual_kbd_loop_init:
	mov byte[is_from_virtual_kbd], 0x1	; update state variable
.virtual_kbd_loop:
	;; read a character, ASCII in al
	mov ah, 0x00
	int 0x16

	cmp al, 0x08 	; backspace
	je change_color_mode

	cmp al, 0x1B 	; esc
	je beep

	;; an enter character signifies the end of a command
	;; so a newline should get printed and then the program should resume
	;; from the main .loop again
	cmp al, 0x0D	; enter
	je .nl_reset_state

	jmp nonewline	; all other characters

;; Update the color_mode variable with a byte from the keyboard
;;
;; CLOBBERS
;; - ax
;; - bl
change_color_mode:
	call readbyte		; get byte from keyboard (in al)
	mov [color_mode], al	; store byte in color_mode variable

	jmp compare_virtual_and_jump

;; Simulates going to a new line
;;
;; CLOBBERS
;; - ax
;; - bh
;; - cx
;; - dx
newline:
	;; Scroll up window
	mov ah, 0x06	; scroll screen up
	mov al, 0x01	; lines to scroll (1)
	mov bh, 0x0F	; bg/fg colour
	mov cx, 0x0000	; upper row num/left col num (both 0)
	mov dh, HEIGHT	; lower row num (24)
	mov dl, WIDTH	; right col num (80)
	int 0x10

	;; Move cursor to beginning of screen
	;; dh already contains HEIGHT
	mov ah, 0x02	; set cursors position
	mov bh, 0x00	; page number
	mov dl, 0x00	; col
	int 0x10

	ret

;; Plays a note on the speaker for a given duration
;;
;; CLOBBERS
;; - ax
;; - bx
;; - cx
beep:
	;; Read duration (0-16 supported)
	mov ah, 0x00	; read keypress
	int 0x16
	;; Read ASCII character is in al
	sub al, 'a' 	; normalise (a=0, b=1, c=...)

	;; interrupt 0x16, ah=0 returns the read scancode in ah
	;; so ah must be reset
	mov     ah, 0
	push    ax	; store on stack

	;; move 182 (0b10 11 011 0) into al
	;; bit 7-6 = channel select (2, PC speaker)
	;; bit 5-4 = access mode (lobyte/hibyte)
	;; bit 3-1 = operating mode (square wave generator)
	;; bit 0   = BCD/binary mode (16-bit binary)
	mov     al, 0b10_11_011_0
	out     PIT_MODECOMMAND_PORT, al	; write to PIT control port

	;; Read byte and convert to a usable frequency
	call    readbyte	; read byte from keyboard (in al)
	mov     ah, 0		; readbyte clobbers ax
	sal     ax, 5		; multiply by 32
	add     ax, 1140

	out     PIT_CH2_DATA_PORT, al	; Output low byte.
	mov     al, ah
	out     PIT_CH2_DATA_PORT, al	; Output high byte

	;; Port 0x61 does a whole lot but only the bottom 2 bits are relevant here
	;; (speaker enable and speaker input select)
	in      al, 0x61	; Preserve previous value
	or      al, 00000011b	; Set bits 1 and 0 (enable speaker, input = channel 2)
	out     0x61, al	; Send new value

	;; mov     bx, 50000	; Pause for duration of note.

	;; multiply duration by 3125
	pop bx		; pull duration value from stack into bx
	push ax		; save ax (contains garbage?)
	mov ax, 3125
	mul bx
	mov bx, ax	; move dur * 3125 into bx
	pop ax		; restore ax

;; play note for a certain duration
.pause1:
	mov     ecx, 65535
.pause2:
	dec     cx	; count down
	jne     .pause2	; if not zero keep counting down

	dec     bx	; decrement duration counter
	jne     .pause1	; keep doing that until it is 0

	in      al, 0x61	; Preserve previous value
	and     al, 11111100b	; Clear bits 1 and 0 (disable speaker, clear channel select)
	out     0x61, al        ; Send new value

	jmp compare_virtual_and_jump

;; Handles all other characters by writing them to the screen
;;
;; CLOBBERS
;; - ah
;; - bx
;; - cx
;; - dx
nonewline:
	;; Write character
	mov ah, 0x09		; write character with attribute
	mov bh, 0x00		; page number
	mov bl, [color_mode]	; BIOS colour code
	mov cx, 0x01		; amount of times to print character
	int 0x10

	;; Get current cursor position
	;; dh = row, dl = col
	mov ah, 0x03	; get cursor position and shape
	int 0x10

	;; if the cursor is at the edge of the screen go to the next line
	;; else move it forward once
	cmp dl, WIDTH
	jge .eol
	jmp .noeol

.eol:
	call newline

	jmp compare_virtual_and_jump

.noeol:
	;; Move cursor forward
	inc dl
	mov ah, 0x02	; set cursor position, dh (row) already set, dl (col) updated on prev line
	int 0x10

	jmp compare_virtual_and_jump

;; Compares the is_from_virtual_kbd state variable to 1 to check if the command
;; came from the virtual keyboard
;; if it did, jump to the virtual keyboard loop
;; if it didn't, jump to the main loop
compare_virtual_and_jump:
	cmp byte[is_from_virtual_kbd], 0x01
	je start.virtual_kbd_loop
	jmp start.loop

;; Reads two characters from the keyboard buffer and converts them into a single byte
;;
;; The conversion happens as follows:
;; 	ASCII 'a' is subtracted from each character (so 'a' = 0, 'b' = 1, ...)
;;	the first character is shifted left by 4
;;	the shifted and non-shifted values are then or'ed together to form a byte
;;
;; RETURNS
;; A byte in al
;;
;; CLOBBERS
;; - ax
;; - bl
readbyte:
	mov ah, 0x00	; Read character
	int 0x16

	;; Read character is in al
	sub al, 'a'	; Normalise
	mov bl, al
	shl bl, 0x04	; First character is upper 4 bits

	mov ah, 0x00	; Read character
	int 0x16

	;; Read character is in al
	sub al, 'a'	; Normalise

	or al, bl	; Combine both characters

	ret

;; Reads a duration from the keyboard
;;
;; RETURNS
;; A duration in al
;;
;; CLOBBERS
;; - ax
;read_duration:
;	;; Read duration (0-16 supported)
;	mov ah, 0x00	; read keypress
;	int 0x16
;
;	;; Read character is in al
;	sub al, 'a' 	; normalise
;
;	ret

;; Variable to store color mode information for writing to the screen
color_mode: db 0x02
;; State variable for detecting whether keystrokes are virtual or real
is_from_virtual_kbd: db 0x00

;; Magic number must be in the last 2 bytes of the sector so
;; fill the binary with zeroes until it is 510 bytes in size
;; (magic number will use up the remaining 2)
times 510 - ($ - $$) db 0
dw 0xAA55 ;; Magic number to mark sector as bootable